- Wireless Power TransferPosted 12 hours ago
- Robot Punchers with ArduinoPosted 1 day ago
- A minimal 3D-printed scalePosted 3 days ago
- Expanding the pins of a microcontrollerPosted 6 days ago
- Let’s create a small level with a matrix displayPosted 1 week ago
- ChatGPT: Writing Code with Artificial IntelligencePosted 1 week ago
- Free Webinar: Arduino IoT Cloud and ESP32 DemoboardPosted 1 week ago
- Maker Faire Rome – The European edition and FAE Technology launch the contest “MY Maker PCBA: your electronics for a better planet”Posted 3 months ago
- Efficient and Compact Stereo Power Amplifier: Unleash High-Quality Audio with the PAM8610Posted 3 months ago
- Terminus FE1.1 USB hub board: the solution to connect four USB devicesPosted 6 months ago
3D LightSquared 8x8x8 LED Cube Soldering Steps
Web site:
http://www.instructables.com/id/3D-LightSquared-8x8x8-LED-Cube-Soldering-Steps/Project Summary:
Soldering Steps of 3D LightSquared 8x8x8 LED Cube
Full Project:
ICStation team has made a wonderful video to show how to soldering the
3D LightSquared DIY Kit 8x8x8 3mm LED Cube White LED Blue Ray
Here are the detailed steps for your reference.
Parameters
Power supply voltage: 4.5~5.5V
PCB size: 11.1*12.7CM
Listing:(some components more than need)
PCB x1
3mm white blue LED x512
XH2.54-40P round female pin x2
20P IC socket x9
74HC573 DIP x9
USB to DC005 cable x1
DC005 power socket x1
18P IC socket x1
ULN2803 DIP x1
40P IC socket x 1
STC12C5A60S2 (with code) x 1
A09-103 Resisters x1
8*8 Self-locking switch x1
10uf 25V electrolytic capacitor x2
12MHz crystals x1
22pf ceramics capacitor x2
470ohm resistor x8
4.7K ohm resistor x2
LED 3mm x1
0.8mm cable x1
Step 1: Check the Font & Back of the PCB
Step 2: Cut the 40P round female pin into single needle
Step 3: Remove the plastic package of the needle
Step 4: Start the soldering
Please be noted that do not put the chip in a wrong direction
Step 5: Make the 512pcs of LED as below
Step 6: Connect all the cathode side (8 layers) and fix to the controller board
Step 7: Soldering finished and check the effect
Bill of Materials:
Listing:(some components more than need)
PCB x1
3mm white blue LED x512
XH2.54-40P round female pin x2
20P IC socket x9
74HC573 DIP x9
USB to DC005 cable x1
DC005 power socket x1
18P IC socket x1
ULN2803 DIP x1
40P IC socket x 1
STC12C5A60S2 (with code) x 1
A09-103 Resisters x1
8*8 Self-locking switch x1
10uf 25V electrolytic capacitor x2
12MHz crystals x1
22pf ceramics capacitor x2
470ohm resistor x8
4.7K ohm resistor x2
LED 3mm x1
0.8mm cable x1
-
Arduino ISP (In System Programming) and stand-alone circuitsWe use an Arduino to program other ATmega without...
- Posted 12 years ago
-
-
-
GSM GPS shield for ArduinoShield for Arduino designed and based on the module...
- Posted 11 years ago
-
Small Breakout for SIM900 GSM ModuleSome post ago we presented a PCB to mount...
- Posted 12 years ago
-
Wireless Power TransferThe concept of transferring energy without wires has always...
- Posted 12 hours ago
-
Robot Punchers with ArduinoJames Bruton is well-known for his (often eccentric) inventions,...
- Posted 1 day ago
-
-
Expanding the pins of a microcontrollerWhat to do when the chosen microcontroller doesn’t have...
- Posted 6 days ago
-
Let’s create a small level with a matrix displayThe low cost of sensors and components allows...
- Posted 1 week ago