Home   >   Posts tagged "OpenStore"
  • Controller with feedback for stepper motor

    Stepper motor feedback controller able to dynamically check the positioning of the shaft and prevent any step loss in 3D printing, CNC, etc. It mounts directly on NEMA17 motors. All management of the controller is entrusted to...

    • Posted 2 weeks ago
    • 0
  • Base for GSM Modem (Excluded)

    Basic board to create, in combination with the FT1308M and FT1128M (not included), a complete GPRS modem to make data connections, calls, send sms. For example, it allows the use of GPS / GSM or GSM-only locators...

    • Posted 2 weeks ago
    • 0
  • IP WiFi camera – 2MPX – ONVIF

    Motorized color IP camera with 2MPX CMOS image sensor with integrated Wi-Fi module. Made respecting the ONVIF (Open Network Video Interface Forum) protocol, it is equipped with a 3.6 mm fixed lens and 11 IR LEDs that...

    • Posted 2 weeks ago
    • 0
  • Maduino Zero SIM808 GSM/GPS Tracker

    Maduino Zero SIM808 GPS Tracker is a board based on the Atmel SAMD21 32 bit microcontroller and on the GPS module GPRS / GSM SIM808. Programmable through the Arduino IDE, it can be used to create IOT...

    • Posted 2 weeks ago
    • 0
  • Waveform generator

    Waveform generator in kit based on ICL8038 chip. It is able to generate sine wave, triangular and square wave output signals. It has status LEDs, switch to select the frequency band, Duty cycle adjustment, distortion adjustment for...

    • Posted 2 weeks ago
    • 0
  • Temperature sensor

    Maxim’s 1-Wire digital temperature sensor.  It measures temperatures between -55 ° C and + 125 °C with an accuracy of 0.5 °C. Each sensor is equipped with a 64-bit serial code stored inside, this allows you to...

    • Posted 2 weeks ago
    • 0
  • Humidity and temperature sensor

    The DHT22 is a basic, low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air, and spits out a digital signal on the data pin (no analog...

    • Posted 2 weeks ago
    • 0
  • Wind sensor with adjustable arm

    Simple but effective sensor capable of detecting wind speed. It contains a magnetic contact that sends an impulsive signal to each rotation of the rotor driven by the force of the wind. Specifications: a wind speed of...

    • Posted 3 weeks ago
    • 0
  • Raspberry Pi NoIR Infrared Camera Board v2.1 (8MP, 1080p)

    The infrared Camera Module v2 (Pi NoIR) has a Sony IMX219 8-megapixel sensor (compared to the 5-megapixel OmniVision OV5647 sensor of the original camera). The Pi NoIR gives you everything the regular Camera Module offers, with one...

    • Posted 3 weeks ago
    • 0
  • Mercury System PB110 – Power Board

    Power Board (PB) is a Mercury system board that provides you with the power management problem, especially for connected and IoT devices. Although the Base Board (BB110) is equipped with a simple power supply system and a...

    • Posted 3 weeks ago
    • 0
  • Rechargeable LIPO 2000 mAh – 7.4 V battery

    Rechargeable LiPo (lithium-polymer) battery with a nominal voltage of 7.4 V and a capacity of 2000 mAh. Discharge capacity: 25C, Balance charge connector: JST-XH, voltage output connector: Deans T, dimensions (mm): 84x34x17, weight: 98 grams. Note: the...

    • Posted 4 weeks ago
    • 0
  • Rechargeable LIPO 2200 mAh – 11.1 V battery

    Rechargeable LiPo (lithium-polymer) battery with 11.1 V nominal voltage and 2200 mAh capacity. Discharge capacity: 25C, Balance charge connector: JST-XH, voltage output connector: Deans T, dimensions (mm): 107x33x25, weight: 175 grams. Note: the battery must be charged...

    • Posted 4 weeks ago
    • 0
  • 3 cell LiPo charger

    Breakout board based on the Texas Instruments BQ76920 integrated circuit designed for charging and discharging 3-cell lithium battery packs. The board can be managed by any programmable processor (for example Arduino with the provided libraries). Thanks to...

    • Posted 4 weeks ago
    • 0
  • Wi-Fi Smart Remote IR Controller – Amazon Alexa and Google Assistant

    Original device, IR (38 kHz) and Wi-Fi that allows installing the “Smart Life or Tuya Life” App to transform your smartphone / tablet into a single remote control capable of replacing all the IR remote controls used...

    • Posted 1 month ago
    • 0
  • Wi-Fi Switch Module 2 Channels – Amazon Alexa and Google Assistant

    Wi-Fi switch module that allows activation and deactivation of 2 loads (lights or electronic devices) operating 220-240 VAC with a maximum current of 5 A (for every output). It can be controlled both via an App (Smart...

    • Posted 1 month ago
    • 0
  • Wi-Fi Switch Module 1 Channel – Amazon Alexa and Google Assistant

    Wi-Fi switch module that allows activation and deactivation of 1 load (lights or electronic devices) operating 90-220 VAC with a maximum current of 10 A. It can be controlled both via an App (Smart Life or Tuya...

    • Posted 1 month ago
    • 0
  • Wi-Fi Smart Switch – Amazon Alexa and Google Assistant

    Simple Wi-Fi switch to be connected directly to the 90-220 VAC mains voltage and capable of controlling a maximum load of 10 A connected to its output. Lights, fans, electric heaters and everything that works with the...

    • Posted 1 month ago
    • 0
  • Shield GSM/GPS/GPRS per Raspberry Pi – SIM7600E-H

    Based on the 4G / 3G / 2G communication module and GNSS SIM7600E-H positioning, this board can be connected to the computer to surf the Internet or connected to the Raspberry Pi to enable functions such as...

    • Posted 1 month ago
    • 0
Next Page »